Surface Care Pty Ltd Warranty Statement
Localised Surface Repair Services
1. Scope of Works
This Warranty Statement forms part of the Terms of Trade of Surface Care Pty Ltd (Surface Care, we, us, our) and applies to all localised surface repair services performed by Surface Care or its authorised subcontractors.
Our repair services cover the following surface types: natural stone, engineered stone, porcelain, ceramic, laminate, natural timber, engineered timber, 2pac (two-pack polyurethane) paint, and other surfaces as agreed in writing. Repairs are carried out using two-part epoxy resin or hardwax fill systems, solvent-based acrylic paints, and polyurethane lacquer clear coat to protect the repair area and match the surrounding surface sheen.
2. Warranty Period
Subject to the exclusions and conditions set out in this Warranty Statement, Surface Care warrants that its localised surface repairs will remain free from defects in workmanship for a period of six (6) months from the date of completion of the repair (Warranty Period).
The Warranty Period commences on the date the repair is completed and signed off, or where no sign-off occurs, the date on which Surface Care notifies the client that the repair is complete.
3. Warranty Coverage
During the Warranty Period, Surface Care will, at its sole discretion, re-perform the repair or provide a reasonable remedy at no additional cost to the client, provided the defect:
a) is attributable to faulty workmanship by Surface Care or its authorised subcontractors;
b) is not the result of any cause listed in the Warranty Exclusions below; and
c) is reported to Surface Care in writing within the Warranty Period.
4. Warranty Exclusions
This warranty does not apply, and Surface Care accepts no liability, where any of the following circumstances exist:
4.1 Physical Damage or Impact
Any scratching, chipping, cracking, impact damage, or other physical interference to the repaired area caused after completion of the repair, whether accidental or intentional.
4.2 Improper Cleaning or Chemical Exposure
Any deterioration of the repair caused by the use of non-pH-neutral cleaning products on or around the repaired area, including but not limited to acidic cleaners, alkaline (basic) cleaners, or products containing alcohol or other solvents. Refer to Section 8 (Care and Maintenance Obligations) for approved cleaning guidance.
4.3 Exterior and Weather-Exposed Surfaces
Any repair located on an exterior surface or a surface exposed to weather, direct sunlight, rain, moisture ingress, or other environmental elements, where such exposure may affect the integrity or appearance of the repair.
4.4 Submerged or Below-Waterline Surfaces
Any repair located below the waterline or in an area subject to standing water, pooling, or prolonged water contact, including but not limited to shower bases, bath bases, basin bowls, and similar wet areas.
4.5 Moveable or Articulating Surfaces
Any repair performed on a surface that is subject to regular movement, flexion, or mechanical stress, including but not limited to doors, toilet lids, cabinet doors, and similar moveable fixtures.
4.6 Benchtop Top Surfaces
Any repair located on the top (horizontal working) surface of a benchtop, countertop, or similar high-traffic work surface, due to the unpredictable nature of chemical exposure, abrasion, heat contact, and frequency of use in these areas.
4.7 Bathroom Surfaces
Any repair located on a surface within a bathroom, ensuite, or wet area environment, due to the elevated humidity, moisture exposure, and chemical exposure (cleaning products, personal care products) typical of these environments.
4.8 Colour Variation and Fading
Any gradual change in colour, tone, or sheen of the repaired area over time. Colour-match fading may occur naturally due to ultraviolet (UV) exposure, cleaning, general wear, or the natural ageing characteristics of the surrounding surface material. Surface Care colour-matches repairs to the existing surface at the time of repair and does not warrant against subsequent colour drift or variation.
5. Non-Transferability
This warranty is personal to the original client who engaged Surface Care to perform the repair and is not transferable to any subsequent owner, occupier, tenant, or other party. In the event of a change of ownership or occupancy of the premises, the warranty is extinguished from the date of transfer.
6. Limitation of Warranty
This warranty is limited to the re-performance of the specific repair that is the subject of the warranty claim. Surface Care does not warrant or guarantee:
a) an exact or permanent colour match to the surrounding surface;
b) the performance of the underlying substrate or surface material;
c) that the repair will be invisible or undetectable under all lighting conditions; or
d) the longevity of the repair beyond the Warranty Period.
7. Australian Consumer Law
Nothing in this Warranty Statement is intended to exclude, restrict, or modify any rights or remedies that the client may have under the Australian Consumer Law (Schedule 2 of the Competition and Consumer Act 2010 (Cth)) or any other applicable consumer protection legislation that cannot lawfully be excluded.
Where services are supplied to a consumer (as defined under the Australian Consumer Law), those services come with guarantees that cannot be excluded, including the guarantee that services will be rendered with due care and skill, will be reasonably fit for purpose, and will be supplied within a reasonable time. If Surface Care fails to comply with a consumer guarantee, the client may be entitled to a remedy under the Australian Consumer Law, the nature of which will depend on whether the failure is major or minor.
8. Care and Maintenance Obligations
To preserve the integrity of the repair and maintain warranty coverage, the client must observe the following care and maintenance requirements:
a) Cleaning: Use only pH-neutral cleaning products on and around the repaired area. Do not use acidic, alkaline, alcohol-based, or solvent-based cleaners, as these may degrade the repair materials.
b) Physical care: Avoid scratching, striking, or applying excessive force to the repaired area. Do not use abrasive pads, steel wool, or scouring agents on or near the repair.
c) Moisture: Avoid prolonged exposure of the repaired area to standing water or excessive moisture. Wipe up spills promptly.
d) Heat: Do not place hot items directly on or adjacent to the repaired area without appropriate protection (e.g., trivets or heat mats).
e) General: Treat the repaired area with the same care as the original surface. The repair materials, while durable, are a localised restoration and not a replacement of the original factory finish.
9. General Provisions
a) This Warranty Statement is governed by the laws of the State or Territory in which the repair services were performed.
b) Surface Care reserves the right to inspect the repaired area before determining whether a warranty claim is valid.
c) Any warranty claim must be submitted in writing to Surface Care within the Warranty Period. Claims submitted after expiry of the Warranty Period will not be accepted.
d) If this Warranty Statement conflicts with any other term of the Terms of Trade, the Terms of Trade shall prevail to the extent of the inconsistency, except to the extent that doing so would contravene the Australian Consumer Law.
e) Surface Care may update this Warranty Statement from time to time. The version applicable to a repair is the version in effect at the date of completion of that repair.
End of Warranty Statement